Cabot's Cabothane Clear Water Based

Get your home looking its best with Cabot's Cabothane Clear Water Based. This clear polyurethane has been specially designed for doors, windows, trim and furniture. Highly durable, it’s hard wearing and has a fast drying finish. No Sanding is required (refer to label for further instructions).
  • Fast Recoat 2 Hours
  • Non Yellowing Product
  • Water Wash Up
  • UV Protection
  • Areas
    Doors, Furniture, Trim, Windows
  • Clean Up
    Water
  • Sizes
    250ML, 500ML, 1L, 4L
  • Sheen
    Matt, Satin, Gloss
  • Coverage
    16 M2/L
  • Recoat Time
    2 Hours
  • Material Data Sheet Gloss
  • Material Data Sheet OB Satin
  • Material Data Sheet WB Satin
Preparation

Note: Fill nail holes, cracks and other defects with Cabot's Wood Tone Putty after applying the first coat of this product for accurate colour matching. Remove stains, dirt, wax, grease and oil with mineral turpentine. Remove any polish with a suitable polish remover. Note: Previously coated interior timber with highly visible scratches, imperfections or surfaces that are severely worn must be sanded prior to coating. Bare Interior Timber Sand the surface smooth using 180 - 240 grit sandpaper. Sand only in the direction of the grain. Remove all traces of sanding dust. Bare Exterior Timber To coat new bare timber immediately, scrub damp timber with Cabot’s New Timber Prep, following label instructions. New Timber Prep will draw out tannins and oils quickly from the surface, allowing you to skip the 4-6 weeks weathering process required for new timber. Always follow New Timber Prep with Cabot’s Deck Clean following label instructions. Previously Coated Interior Timber

1. Thoroughly clean the surface with Cabot's Floor Clean and allow to dry.

2. Apply one coat to a small test area. Allow to dry for 3 hours. Press sticky tape firmly to the surface and pull off quickly. If the coating comes off, sand back further to a sound surface. Previously Coated Exterior Timber For best results, remove back to bare timber using a paint stripper, or sanding. For exterior surfaces only, clean with Cabot's Deck Clean following label instructions.

Apply with Brush, Spray
Application

Note: Do not shake can

1. Stir thoroughly with a broad flat paddle before and during use.

2. Apply with a good quality brush or spray gun. If spraying, back brushing is recommended. If brushing, always brush in the direction of the grain.

3. Allow to dry for a minimum of 2 hours. For best results, lightly sand to remove any grain raise using 240 grit paper. Remove all sanding dust.

4. Apply 2nd & 3rd coats as above.

Once the surface becomes excessively scratched and worn, it's time for a re coat.

1. Thoroughly clean the surface with Cabot's Floor Clean and allow to dry.

2. Apply one coat to a small test area. Allow to dry for 3 hours. Press sticky tape firmly to the surface and pull off quickly. If the coating comes off, sand back further to a sound surface.

Range

Base colours below are available instore to purchase. From these colour bases, you can tint to 100’s of colours. To view our range, view the colour visualiser.

Clear
Clear on Treated Pine
Clear
Clear on Rimu
Clear
Clear on Macrocarpa

All colours displayed on this page show 2 coats.
Colour varies depending on your timber type.

Sheen

Matt
Satin
Gloss

Available sizes

250 ML
500 ML
1 LITRE
4 LITRE

Product Calculator

If you are unsure on how much product you need, please use our product calculator. Please note minimum length/width value is 1 metre and maximum is 50 metres.

1metre
1metre
2coats
Calculate
0 Total SQM
  • 0 SQM
  • 0 Litre