Cabot's Deck & Exterior Stain Water Based

Forget reapplying again and again – Cabot's Water Based Deck & Exterior Stain lasts twice as long as traditional decking stains. This highly durable stain has been designed to rejuvenate and transform the colour of all exterior timber, delivering a long lasting, beautiful result. Give your decking and furniture a new lease of life.
  • Fast Recoat 2 Hours
  • Dirt & Mould Resistant
  • Water Repellent
  • UV Protection
  • Water Wash Up
  • Areas
    All exterior timber, Decks
  • Clean Up
    Water
  • Sizes
    250ML, 1L, 10L, 5L
  • Coverage
    12 M2/L
  • Recoat Time
    2 Hours
  • Material Data Sheet
Preparation

New Bare Timber

To coat new bare timber immediately, scrub damp timber with Cabot’s New Timber Prep, following label instructions. New Timber Prep will draw out tannins and oils quickly from the surface, allowing you to skip the 4-6 weeks weathering process required for new timber. Always follow New Timber Prep with Cabot’s Deck Clean following label instructions. Remove excess water from the surface with squeegee on Cabot’s Deck Prep brush, and allow timber to dry for at least 1 hour. Note: Cooler conditions could slow down the drying time of the timber.

Previously Painted or Varnished Timber

Remove back to bare timber using a paint stripper, or sanding. For exterior surfaces clean with Cabot's Deck Clean following label instructions.

Previously Stained and Oiled Timber

For exterior surfaces clean with Cabot’s Deck Clean following label instructions. Test if the surface is ready for coating by sprinkling water on the timber. If the water beads on the surface, repeat the application of Deck Clean. If water is absorbed into timber, it is ready for coating. For a more transparent look, sand timber back to bare then clean with Cabot's Deck Clean before coating. Weathered and Grey Timber For best results, sand timber back to fresh substrate. Clean with Cabot's Deck Clean following label instructions.

Apply with Brush, Decking Applicator
Application

1. Stir thoroughly with a broad flat paddle before and during use.

2. Apply liberally along the length of the board including exposed edges and end grain by brush or pad applicator. The initial milky colour helps with even product application, drying to a semi-transparent finish.

3. Allow the first coat to dry for 2 hours and then apply a second coat using the same method.

N/A

Range

Base colours below are available instore to purchase. From these colour bases, you can tint to 100’s of colours. To view our range, view the colour visualiser.

Aged Oak
Aged Oak on Treated Pine
Ash Black
Ash Black on Treated Pine
Blackbean
Blackbean on Treated Pine
Blackburn
Blackburn on Treated Pine
Cedar
Cedar on Treated Pine
Charcoal
Charcoal on Treated Pine
Classic Walnut
Classic Walnut on Treated Pine
Dense Forest
Dense Forest on Treated Pine
Desert Tusk
Desert Tusk on Treated Pine
Ebony
Ebony on Treated Pine
Golden Pine
Golden Pine on Treated Pine
Hunter Grey
Hunter Grey on Treated Pine
Karaka
Karaka on Treated Pine
Kwila
Kwila on Treated Pine
Lancewood
Lancewood on Treated Pine
Liquid Amber
Liquid Amber on Treated Pine
Maungakiekie
Maungakiekie on Treated Pine
Mission Brown
Mission Brown on Treated Pine
New Rustic
New Rustic on Treated Pine
Puka
Puka on Treated Pine
Red Rata
Red Rata on Treated Pine
Sandstone
Sandstone on Treated Pine
Silver Beech
Silver Beech on Treated Pine
Weathered Cedar
Weathered Cedar on Treated Pine

All colours displayed on this page show 2 coats.
Colour varies depending on your timber type.

Available sizes

250 ML
1 LITRE
10 LITRE
5 LITRE

Product Calculator

If you are unsure on how much product you need, please use our product calculator. Please note minimum length/width value is 1 metre and maximum is 50 metres.

1metre
1metre
2coats
Calculate
0 Total SQM
  • 0 SQM
  • 0 Litre